1066 Compressor / Limiter / Gate Sinyal İşleyici
Teknik Özellikler:- Input Connectors XLR and 1/4" TRS (Pin 2 and tip hot)
- Input Type Electronically balanced/unbalanced, RF filtered
- Input Impedance Balanced > 50 kOhm, unbalanced >25 kOhm
- Max Input > +24 dBu balanced or unbalanced
- CMRR Typically >50 dB at 1 kHz
- Output Connectors XLR and 1/4" TRS (Pin 2 and tip hot)
- Output Type Servo-balanced/unbalanced, RF filtered
- Output Impedance Balanced 120 Ohm, unbalanced 60 Ohm
- Max Output > +21 dBm balanced, > +20 dBm unbalanced
- Sidechain Input Connector 1/4" Unbalanced (Tip-Sleeve)
- Sidechain Input Type Unbalanced, RF filtered
- Sidechain Impedance >10 kOhm
- Sidechain Max Input Level >+24 dBu
- Sidechain Output Connector 1/4" Balanced TRS (tip hot)
- Sidechain Output Type Impedance balanced, RF filtered
- Sidechain Output Impedance Balanced 2 kOhm, unbalanced 1 kOhm
- Sidechain Max Output Level >+21 dBu balanced or unbalanced
- Bandwidth 20 Hz to 20 kHz, +0/0.5 dB
- Frequency Response 0.35 Hz to 90 kHz, +0/-3 dB
- Noise < -95 dBu, unweighted, 22 kHz measurement bandwidth
- Dynamic Range > 118dB, unweighted
- THD+Noise 0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), < 0.1% any amount of compression up to 40 dB, 1 kHz
- IMD < 0.1% SMPTE
- Interchannel Crosstalk < -80 dB 20Hz to 20 kHz
- Stereo Coupling True RMS Power Summing
- Compressor Threshold Range -40 dBu to +20 dBu
- Compressor Ratio 1:1 to infinity:1
- Compressor Threshold Characteristic Selectable OverEasy® or hard knee
- Compressor Attack/Release Characteristic AutoDynamic™
- Compressor Attack/Release Modes Selectable Manual or Auto
- Compressor Manual Attack Time Scalable program-dependent
- Compressor Manual Release Time Scalable program-dependent
- Compressor Auto Attack Time Program-dependent
- Compressor Auto Release Time Program-dependent
- Compressor Output Gain -20 to +20 dB
- Limiter Threshold Range +4 dBu to +24 dBu (off)
- Limiter Ratio infinity:1
- Limiter Type PeakStopPlus® two-stage limiter
- Limiter Stage 1 PeakStop® brickwall limiter
- Limiter Stage 1 Attack Time Zero
- Limiter Stage 1 Release Time Zero
- Limiter Stage 2 Predictive intelligent program limiter
- Limiter Stage 2 Attack Time Program-dependent
- Limiter Stage 2 Release Time Program-dependent
- Expander/Gate Threshold Range Off to +15dBu
- Expander/Gate Ratio 1:1 to 30:1
- Expander/Gate Attack Time < 100 µsec
- Expander/Gate Release Time Program-dependent
- SC Ext. Switch Routes the external sidechain input signal to the detector
- SC Mon. Switch Routes the sidechain signal to the output, interrupting the normal audio
- OverEasy® Switch Activates the OverEasy compression function
- Countour Switch Activates the frequency-dependent detector function
- Auto Switch Activates automatic program-dependent attack and release times, disabling the manual Attack and Release controls
- I/O Meter Switch Switches between monitoring input and output levels on the Input/Output Level meter
- Bypass Switch Activates the direct input-to-output hard-wire relay bypass. Relay automatically hard-wire bypasses unit at power-down and provides a power-on delay of 1.5 sec.
- Operating Level Switch (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneoulsy for both input and output levels
- ST Link Switch Link both channels for stereo operation. Channel One becomes the master
- Gain Reduction Meter 12-segment LED bar graph at 1, 2, 4, 6, 9, 12, 15, 18, 21, 24, 27 and 30 dB
- I/O Meter 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu
- Compressor Threshold Meter 3-segment LED bar graph at Below (-), OverEasy and Above (+)
- Expander/Gate Threshold Meter 2-segment LED bar graph at Below (-) and Above (+)
- Limiter Threshold Meter 1 LED to indicate PeakStopPlus™ limiting
- Function Switches LED indicator for each front-panel switch
- Output Transformer Options Jensen® JT-123-dbx or JT-11-dbx, BCI RE-123-dbx or RE-11-dbx
- Operating Voltage 100-120 VAC 50/60 Hz 200-240 VAC 50/60 Hz
- Power Consumption 20 Watts
- Fuse 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T
- Power Connector IEC receptacle
- Dimensions 1.75"Hx19"Wx9"D (4.4cmx48.3cmx20.1cm)
- Unit Weight 5.1 lbs. (2.3 kg)
- Shipping Weight 7.5 lbs. (3.4 kg)
